Get The Important Preparation Guide With 300-510 Dumps
Get Totally Free Updates on 300-510 Dumps PDF Questions
Conclusion
Building your skills and awareness around the dictates of the Cisco 300-510 exam will bring out the desired results. Efficiency begins with appropriate skills, thus indulging in official training and learning from self-study resources such as books should be the ultimate goal. If you wish to operate within the networks for the Service Provider, then this test is definitely what you need.
Introduction to Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
It is a 90-minute test affiliated with the CCNP Service Provider and Cisco Accredited Professional-Service Provider VPN Services Implementation certifications. Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) exam tests the candidate's knowledge of integrating VPN services, including Layer 2, Layer 3, and IPv6, from the service provider. Different types of 310-510 SPRI practice test helps the students to prepare for the exam.
Topics of Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Exam
These core topics of 310-510 SPRI practice test listed below are general recommendations for the material that is likely to be used for the examination. However, on any delivery of the test, other similar topics could also appear. The guidelines below can update at any time without notice to better represent the contents of the 310-510 SPRI exam dumps pdf and for clarity purposes.
It is recommended that, where possible, the applicant use these courses and/or other resources to provide background information on the exam objectives. The syllabus for the Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) examination is listed below in detail for each section of 300-510 SPRI exam dumps:
- Implement PIM-SM Enhancements
- Troubleshoot OSPF, ISIS, and BGP
- Implement Multiarea IS-IS
- Implement and verifying the PIM-SM protocol
- Influencing Border Gateway Protocol Route Selection
- Implement Route Redistribution
- Implementing and Verifying Open Shortest Path First Multiarea Networks
- Securing BGP in Service Provider Networks
- Troubleshooting Routing Protocols
- Implement BGP Security Options
- Implement Multicast Source Discovery Protocol (MSDP) in the interdomain environment
- Implement mechanisms for dynamic Rendezvous Point (RP) distribution
- Deploying IPv6 Tunneling Mechanisms
- Implementing PIM-SM Enhancements
- Implementing and Verifying Intermediate System to Intermediate System Multilevel Networks
- Implement Cisco MPLS TE
- Implementing Distributed Rendezvous Point Solution in Multicast Network
- Scaling BGP in Service Provider Networks
- Implement Tunnels for IPv6
- Implementing Segment Routing
- Implement MPLS in the Service Provider Core
- Configure and Verify Interior Gateway Protocol (IGP) Segment Routing
- Describing Segment Routing Traffic Engineering (SR-TE)
NEW QUESTION 49
What is the difference between basic IS-IS and OSPF packet types?
- A. IS-IS and OSPF use Hello packets, but only OSPF uses DBD packets.
- B. IS-IS and OSPF use link-state update packets, but only OSPF uses link-state ACK packets.
- C. IS-IS and OSPF use area packets, but only IS-IS uses sequence number packets.
- D. IS-IS and OSPF use link-state update packets, but only IS-IS uses DBD packets.
Answer: A
NEW QUESTION 50
Refer to the exhibit.
Router 1 has established an SR-TE tunnel with router 2. Which statement describes this configuration?
- A. Router 1 is the head-end tunnel and has dynamically chosen a path to router 2.
- B. Router 2 is the head-end tunnel and has explicitly set a path to router 1.
- C. Router 1 has a list of labels used to explicitly lay out a path to router 2.
- D. Router 1 and router 2 have a bidirectional tunnel set up with dynamic path selection.
Answer: A
NEW QUESTION 51
Refer to the exhibit.
What is the relationship between Router 1 and Router 2?
- A. Router 1 and Router 2 centrally learn the topology of the network to aid in SR-TE path selection for peers.
- B. Router 1 centrally learns the topology of the network to aid in SR-TE path selection, and Router 2 is a node that feeds Router 1 topology information.
- C. Router 1 and Router 2 are participating in SR-TE tunnels and are both head-end routers.
- D. Router 2 is the head-end router in an SR-TE tunnel, and it is learning topology of the network from the PCE enabled on Router 1.
Answer: D
NEW QUESTION 52
What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)
- A. A static IPv4 address must be configured.
- B. A dynamic IPv6 address must be configured.
- C. Cisco Express Forwarding must be enabled.
- D. A dynamic IPv4 address must be configured.
- E. A static IPv6 address must be configured.
- F. Each tunnel endpoint must support IPv4 and IPv6.
Answer: A,E,F
NEW QUESTION 53
Refer to the exhibit. Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally.
Which two statements describe the problem? (Choose two.)
- A. The two routers have password mismatch issues
- B. The two routers have the same network ID
- C. The two routers are in the same area
- D. The two routers are in different subnets
- E. The two routers are in different areas
Answer: D,E
NEW QUESTION 54
Refer to the exhibit. An engineer is addressing an IS-IS design issue which is running within the topology.
All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet.
Which statement about the design is true?
- A. R5 prefers to use R4 as the next hop for all routes
- B. R1 prefer to use R5 as the next hop to reach R4
- C. R4 prefer to reach R5 using R1 as the next hop
- D. All links have equal cost if the default metric is used
Answer: D
NEW QUESTION 55
Refer to the exhibit.
A network operator must inject a Level 1 route from XR2 (10.16.16.0/24) into the ISIS topology. Which configuration allows the injection in a way that XR3 and XR1 have a valid and working route for 10.16.16.0/24?
- A. Option B
- B. Option D
- C. Option A
- D. Option C
Answer: D
NEW QUESTION 56
Refer to the exhibit. VPN users that are connected to PE routers are facing network issues.
Traffic that originates from CE1 drops before reaching CE2. An engineer finds no outgoing traffic statistics on PE1 and PE2 routers toward CE devices and finds that the PE1 router is running the older software image. Which action must be implemented to resolve the issues?
- A. Advertise P1 router loopback on PE1 in OSPF.
- B. Enable LDP protocol on PE1 and PE2 routers.
- C. Advertise PE2 router loopback on PE1 in OSPF.
- D. Enable CEF-based forwarding on PE1 router.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_basic/configuration/xe-3s/mp-basic-xe-3s- book/mp-mpls-cisco-rtrs.html
NEW QUESTION 57
An engineer applied the summarization configuration on R1 for four networks (192.168.20.0/24 to
192.168.23.0/24) in area 1 and eight networks (192.168.32.0/24 to 192.168.39.0/24) in area 2 to stop the flooding of all the customer routes. While checking the routing table of R2, the engineer noticed that R1 is still sending only specific routes to R2.
Which configuration should the engineer apply on R1 to summarize routes?
- A. Option B
- B. Option D
- C. Option A
- D. Option C
Answer: D
NEW QUESTION 58
Drag and Drop Question
Drag and drop the features from the left into the order of operations for SRv6 SRH field creation and forwarding on the right.
Answer:
Explanation:
NEW QUESTION 59
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have different process IDs
- B. The two devices have different network types
- C. The two devices have the same area ID
- D. The two devices have different router IDs
Answer: B
Explanation:
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html
NEW QUESTION 60
In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?
- A. The receiver explicitly requests its desired traffic from the RP on the shared tree.
- B. The RP on the shared tree floods traffic out of all PIM configured interfaces.
- C. The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic.
- D. The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.
Answer: D
NEW QUESTION 61
A network engineer is troubleshooting OSPF multiare A.
Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?
- A. routing process enabled by default on all interfaces
- B. hierarchical CLI
- C. DR support for topology management
- D. show ip ospf topology command
Answer: B
Explanation:
Reference:
guide/rc40xr12k_chapter4.html#con_1059437
NEW QUESTION 62
Refer to the exhibit.
An engineer has configured all routers in the environment to run IS-IS Level 1 and Level 2 routing. The engineer wants traffic from R1 to R5 to pass via R2. but IS-IS routing has calculated the best path via R4.
Which action corrects the problem?
- A. Set the link metric for the link from router R1 to router R4 to 30 or more.
- B. Configure routers R1, R2, and R5 for Level 1 routing only.
- C. Set the link metric on R2 for the links from router R2 to routers R3 and R4 to 30 or more.
- D. Configure routers R1, R4, and R5 for Level 2 routing only.
Answer: A
NEW QUESTION 63
Refer to the exhibit.
A network operator is working to filter routes from being advertised that are covered under an aggregate announcement. The receiving router of the aggregate announcement block is still getting some of the more specific routes plus the aggregate. Which configuration change ensures that only the aggregate is announced now and in the future if other networks are to be added?
- A. Set each specific route in the AGGRO policy to drop instead of suppress-route
- B. Filter the routes on the receiving router
- C. Set each specific route in the AGGRO policy to remove instead of suppress-route
- D. Configure the summary-only keyword on the aggregate command
Answer: D
NEW QUESTION 64
After an engineer configures BGP in R1, it starts receiving this message
*Jun 29 13:30:50.122: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down User reset Jun 29 13:30:52.341: %BGP-3-NOTIFICATION: sent to neighbor 192.168.10.1 2/6 (unacceptable hold time)
0 bytes
Which action makes the peering come back up again?
- A. Set up a hold-down timer higher.
- B. Set up a hello timer higher.
- C. Make a soft reset to the peer.
- D. Set up a minimum hold-down timer higher.
Answer: D
NEW QUESTION 65
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have different process IDs
- B. The two devices have different network types
- C. The two devices have the same area ID
- D. The two devices have different router IDs
Answer: B
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html
NEW QUESTION 66
Refer to the exhibit.
An engineer applied the configuration on R1 to prevent network 192.168.1.0/24 from being propagated outside of area 5. After the change, users have reported they are not able to access any of the application servers that were working before. While checking the routing table of the peer router. The engineer notices R1 stopped propagating any routes outside are 5. Which action must be taken to fix the problem?
- A. Change the prefix-list action to permit and add an explicit deny statement for network 192.168.1.0/24
- B. Configure an additional filter-list on R1 for inbound traffic to allow external router into area 5.
- C. Reconfigure the filter-list statement to apply in the inbound direction
- D. Add a permit statement for 0.0.0.0/0 le 32 to the end of the prefix-list 10 override the implicit deny.
Answer: D
NEW QUESTION 67
......
Prepare With Top Rated High-quality 300-510 Dumps For Success in Exam: https://www.pass4guide.com/300-510-exam-guide-torrent.html
300-510 Free Certification Exam Easy to Download PDF Format 2023: https://drive.google.com/open?id=1p2nNKunUWY_JLXZFGSPRU-kAUF9wLNkx