Get Prepared for Your 200-301 Exam With Actual Cisco Study Guide!
Pass Your Next 200-301 Certification Exam Easily & Hassle Free
Average Salary of 200-301 CCNA Exam: Cisco Certified Network Associate Certified Professionals
The average salary of a 200-301 CCNA Exam: Cisco Certified Network Associate Exam Certified Expert in:
- Europe - 71,211 EURO
- United State - 97,112 USD
- England - 67,658 POUND
- India - 6,121,000 INR
Security Fundamentals: This objective assesses the experience of the professionals in:
- Setting Layer 2 protection attributes
- Explaining the key protection concepts (exploits, vulnerabilities, and threats)
- Describing security policies points, such as management, complexity, and alternatives for password
- Verifying and setting access control lists
- Describing the elements of security programs (training, physical access management, and user awareness)
- Setting device access management utilizing local passwords
- Describing remote access and VPNs
Programmability & Automation: The last area checks the competence of the individuals in:
- Describing characteristics of the APIs that are based on the REST
- Understanding of JSON encoded information
- Comparing traditional networks with controller-based networking
- Comprehension of the capabilities of configuration management mechanisms Ansible, Chef, and Puppet
- Describing controller-based & software defined architectures
NEW QUESTION 272
Which two statements about stateful firewalls in an enterprise network are true? (choose two)
- A. They can use information about previous packets to make decisions about future packets
- B. They are more susceptible to DoS attacks than stateless firewalls
- C. They can track the number of active TCP connections
- D. They can filter HTTP and HTTPS traffic in the inbound direction only
- E. They are most effective when placed in front of the router connected to the internet
Answer: A,C
NEW QUESTION 273
Refer to the exhibit. How does the router manage traffic to 192.168.12.16?
- A. It chooses the OSPF route because it has the longest prefix inclusive of the destination address.
- B. It chooses the EIGRP route because it has the lowest administrative distance.
- C. It load-balances traffic between all three routes.
- D. It selects the RIP route because it has the longest prefix inclusive of the destination address.
Answer: A
NEW QUESTION 274
Refer to the exhibit.
The network administrator wants VLAN 67 traffic to be untagged between Switch 1 and Switch 2 while all other VLANs are to remain tagged.
Which command accomplishes this task?
- A. switchport access vlan 67
- B. switchport trunk native vlan 67
- C. switchport private-vlan association host 67
- D. switchport trunk allowed vlan 67
Answer: B
NEW QUESTION 275
When deploying syslog, which severity level logs informational messages?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Section: IP Services
Explanation/Reference: https://en.wikipedia.org/wiki/Syslog
NEW QUESTION 276
Drag and drop the Rapid PVST+ forwarding slate actions from the loft to the right. Not all actions are used.
Answer:
Explanation:
NEW QUESTION 277
What are two reasons to use multicast to deliver video traffic, instead of unicast or broadcas? (choose two)
- A. it supports distributed applications
- B. it provides reliable TCP transport
- C. it enables multiple clients to receive the video stream simultaneously
- D. it enables multiple clients to send video streams simultaneously
- E. it enables multiple servers to send video streams simultaneously
Answer: A,C
NEW QUESTION 278
Why would VRRP be implemented when configuring a new subnet in a multivendor environment?
- A. to ensure that the spanning-tree forwarding path to the gateway is loop-free
- B. to enable normal operations to continue after a member failure without requiring a change In a host ARP cache
- C. when a gateway protocol is required that support more than two Cisco devices for redundancy
- D. to interoperate normally with all vendors and provide additional security features for Cisco devices
Answer: C
NEW QUESTION 279
Refer to the exhibit.
An engineer configured NAT translations and has verified that the configuration is correct.
Which IP address is the source IP?
- A. 172.23.103.10
- B. 10.4.4.4
- C. 172.23.104.4
- D. 10.4.4.5
Answer: C
NEW QUESTION 280
EIGRP TS
Question
Refer to the topology. Your company has connected the routers R1, R2 and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the EIGRP issues between the various routers. Use the appropriate show commands to troubleshoot the issues.
The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32 and 10.4.4.6/32 are not appearing in the routing table of R5.
Why are the interfaces missing?
- A. The interfaces are shutdown, so they are not being advertised.
- B. R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
- C. Automatic summarization is enabled, so only the 10.0.0.0 network is displayed.
- D. The loopback addresses haven't been advertised, and the network command is missing on R4.
Answer: D
NEW QUESTION 281
When you enable PortFast on a switch port, the port immediately transitions to which state?
- A. Listening
- B. Learning
- C. Blocking
- D. Forwarding
Answer: D
NEW QUESTION 282
If a router has four interfaces and each interface is connected to four switches, how many broadcast domains are present on the router?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 283
DRAG DROP
Drag and drop the network protocols from the left onto the correct transport services on the right.
Answer:
Explanation:
NEW QUESTION 284
A network engineer must configure two new subnets using the address block 10 70 128 0/19 to meet these requirements:
* The first subnet must support 24 hosts
* The second subnet must support 472 hosts
* Both subnets must use the longest subnet mask possible from the address block Which two configurations must be used to configure the new subnets and meet a requirement to use the first available address in each subnet for the router interfaces? (Choose two )
- A. interface vlan 155
ip address 10.70.155.65 255.255.255.224 - B. interface vlan 1234
ip address 10.70.159.1 255.255.254.0 - C. interface vlan 1148
ip address 10.70.148.1 255.255.254.0 - D. interface vlan 3002
ip address 10.70.147.17 255.255.255.224 - E. interface vlan 4722
ip address 10.70.133.17 255.255.255.192
Answer: C,D
NEW QUESTION 285
Refer to the exhibit.
A new subnet with 60 hosts has been added to the network.
Which subnet address should this network use to provide enough usable addresses while wasting the fewest addresses?
- A. 192.168.1.56/26
- B. 192.168.1.56/27
- C. 192.168.1.64/26
- D. 192.168.1.64/27
Answer: C
NEW QUESTION 286
Which characteristics are representative of a link-state routing protocol? (Choose two.)
- A. utilizes event-triggered updates
- B. calculates shortest path
- C. provides common view of entire topology
- D. exchanges routing tables with neighbors
- E. utilizes frequent periodic updates
Answer: A,C
NEW QUESTION 287
Refer to the exhibit.
Router R2 is configured with multiple routes to reach network 10 1.1 0/24 from router R1. What protocol is chosen by router R2 to reach the destination network 10.1 1 0/24?
- A. EIGRP
- B. eBGP
- C. OSPF
- D. static
Answer: D
NEW QUESTION 288
Which two command sequences must be configured on a switch to establish a Layer 3 EtherChannel with an open-standard protocol? (Choose two)
- A. interface port-channel 10
switchport
switchport mode trunk - B. interface GigabitEthernet0/0/1
channel-group 10 mode active - C. interface GigabitEthernet0/0/1
channel-group 10 mode on - D. interface GigabitEthernet0/0/1
channel-group 10 mode auto - E. interface port-channel 10
no switchport
ip address 172.16.0.1.255.255.255.0
Answer: B,E
NEW QUESTION 289
How will Link Aggregation be Implemented on a Cisco Wireless LAN Controller?
- A. When enabled, the WLC bandwidth drops to 500 Mbps.
- B. To pass client traffic, two or more ports must be configured.
- C. The EthernetChannel must be configured in "mode active".
- D. One functional physical port is needed to pass client traffic.
Answer: D
NEW QUESTION 290
......
Each of these objectives comes with a specific set of skills that are described in detail below:
This topic includes the following skills: explaining the network components role; describing network topology architectures; comparing cabling and physical interface types; defining cable and interface issues (collisions, speed, errors, mismatch duplex); comparing TCP and UDP; customizing and verifying subnetting IPv4 subnetting and addressing; describing the necessity of private IPv4 addressing; customizing and verifying IPv6 prefix and addressing; comparing IPv6 address types; verifying IP parameters for Client OS (Linux, Windows, Mac OS); describing switching principles; explaining wireless concepts; explaining virtualization basics (virtual machines).
Within this domain, the examinees need to demonstrate their ability to: interpret the routing table components (routing protocol code, network mask, prefix, next hop, last resort gateway, administrative distance, metric); customize IPv4 and IPv6 static routing (host route, default route, floating static, network route); identify how a router makes a forwarding decision by default (administrative distance, longest match, routing protocol metric); customize and verify single area OSPFv2 (point-to-point, neighbor adjacencies, router ID, broadcast); explain the objective of first hop redundancy protocol.
This subject area evaluates the following skills of the candidates: identifying core security concepts (vulnerabilities, threats, exploits, mitigation techniques); explaining security program elements (physical access control, user awareness, and training); customizing device access control using local passwords; explaining the elements of security password policies, including complexity, management, password alternatives (multifactor authentication, certificates, and biometrics); describing site-to-site VPNs and remote access; configuring and verifying access control lists; configuring security features of Layer 2 (dynamic ARP inspection, DHCP snooping, port security); differentiating accounting, authentication, and authorization concepts; describing WPA, WPA2, and WPA3 security protocols; customizing WLAN with the help of WPA2 PSK.
Here the applicants need to demonstrate that they are capable of: explaining how automation affects network management; distinguishing traditional networks from controller-based networking; describing software defined and controller-based architectures (fabric, overlay, underlay); distinguishing traditional campus device management from Cisco DNA Center enabled device management; describing REST-based APIs characteristics (data encoding, CRUD, HTTP verbs); recognizing the abilities of Puppet, Chef, and Ansible configuration management mechanisms; interpreting JSON encoded data.
This objective combines the questions that check competency of the test takers in: customizing and verifying within source NAT with the help of static and pools; customizing and verifying NTP operating in a server and client mode; explaining the function of DHCP and DNS within the network; explaining the role of SNMP in executing network operations; describing the utilization of syslog features including facilities and levels; customizing and verifying DHCP relay and client; explaining the forwarding per-hop behavior (PHB) for QoS, including classification, queuing, marking, shaping, congestion, policing; customizing remote access network devices with the help of SSH; describing the function of TFTP/FTP in the network.
Ace 200-301 Certification with 604 Actual Questions: https://www.pass4guide.com/200-301-exam-guide-torrent.html
Free Cisco 200-301 Exam Question Practice Exams: https://drive.google.com/open?id=13ILrTX_MQ4QgDm9XXFJ95dIiDKWwgW67