Assume NACE NACE-CIP1-001 Dumps PDF Are going to be The Best Score
CIP Level 1 NACE-CIP1-001 Exam and Certification Test Engine
NEW QUESTION 27
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. observe and direct the work of the contractors.
Answer: B
NEW QUESTION 28
To achieve consistently accurate results with ALL alt test equipment
- A. wash your hands before sampling.
- B. wear gloves when sampling.
- C. avoid placing the sample discs on a surface.
- D. calibrate the instrument in the field.
Answer: A
NEW QUESTION 29
ASTM Standards are applicable:
- A. In Asia
- B. When specified
- C. In North America
- D. In the USA
Answer: B
NEW QUESTION 30
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Anode
- C. Cathode
- D. Reference Cell
Answer: D
NEW QUESTION 31
Osmotic blistering is most likely to occur as a result of
- A. applying tine coating too thin.
- B. airless spray application
- C. overcoating a surface contaminated with chemical salts.
- D. inadequate anchor pattern/surface profile.
Answer: B
NEW QUESTION 32
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Profilometer
- C. Needle pressure gauge
- D. Psychrometer
Answer: B
NEW QUESTION 33
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. Only if the specification requires it
- B. In the office only
- C. At all times
- D. In the field only
Answer: C
NEW QUESTION 34
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- C. NACE 2/SSPC SP10
- D. their best judgment based on similar projects and specifications.
Answer: B
NEW QUESTION 35
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. blistering.
- B. cracking.
- C. alligatoring.
- D. checking.
Answer: D
NEW QUESTION 36
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Achieve consensus through negotiation
- B. Call the supervisor
- C. Never change his/her mind
- D. Go with the majority opinion
Answer: B
NEW QUESTION 37
Non Conformance Reports are completed by the Inspector:
- A. In every instance that an item does not meet the specification requirements
- B. In accordance with the specification's definition of a non-conformance
- C. When the Inspector and Contractor deem it to be a significant non-conforming item
- D. When the Inspector deems it to be a significant non-conforming item
Answer: C
NEW QUESTION 38
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Abrasive blast nozzles
- B. Airless spray equipment
- C. Hand tools
- D. Power tools
Answer: D
NEW QUESTION 39
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Placing the gauge along the longitudinal axis
- C. Using a damaged gauge
Answer: A,C
NEW QUESTION 40
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Edges and corners
- C. Complex geometric shapes
- D. Welds
Answer: A
NEW QUESTION 41
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
Answer: D
NEW QUESTION 42
NACE SP 0178 is a standard for:
- A. Structural steel to be coated for Atmospheric Service
- B. Tanks and Vessels to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Stainless steel pipe to be Externally Coated
Answer: C
NEW QUESTION 43
Stripe coats are best applied by:
- A. Conventional spray
- B. High volume low pressure spray
- C. Brush
- D. Airless spray
Answer: C
NEW QUESTION 44
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC PA 2
- B. NACE SP 0178
- C. NACE SP 0188
- D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
Answer: D
NEW QUESTION 45
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. replica tape
- C. surface comparator
- D. needle pressure gauge
Answer: D
NEW QUESTION 46
Check abrasive blast pressure close to the
- A. blast nozzle
- B. compressor
- C. blast pot
- D. substrate
Answer: A
NEW QUESTION 47
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. what materials were used.
- B. how the item was coated.
- C. when the coating will be reapplied.
- D. what items were coated.
Answer: B
NEW QUESTION 48
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the less aggressive profile
- B. Use another method as the comparator method is too subjective
- C. Record the segment with the more aggressive profile
- D. Record your result by identifying two segments
Answer: A
NEW QUESTION 49
Polymerization is the process of:
- A. All thermoplastic coatings
- B. All organic coatings
- C. Monomers telegraphing
- D. Monomers joining together
Answer: D
NEW QUESTION 50
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 70% of the specified maximum thickness
- C. 100% of the specified maximum thickness
- D. 90% of the specified maximum thickness
Answer: A
NEW QUESTION 51
The least effective method of surface cleaning is most likely
- A. dry grit blasting.
- B. hand tool cleaning.
- C. water blasting.
- D. power tool cleaning.
Answer: B
NEW QUESTION 52
......
Use NACE-CIP1-001 Exam Dumps (2021 PDF Dumps) To Have Reliable NACE-CIP1-001 Test Engine: https://www.pass4guide.com/NACE-CIP1-001-exam-guide-torrent.html
NACE-CIP1-001 PDF Recently Updated Questions Dumps to Improve Exam Score: https://drive.google.com/open?id=1b0WYe69Up32GRarID4z1vqMqU8qJM1Pn