[Mar-2025] 100% Guarantee Download NACE-CIP1-001 Exam Dumps PDF Q&A
Kickstart your Career with Real Updated Questions
NEW QUESTION # 54
The Inspector should record the serial numbers of inspection instruments:
- A. Only when verifying accuracy of the instrument
- B. Each time the instrument is used
- C. Only if the specification requires it
- D. Only if the instrument is suspected of not working properly
Answer: B
NEW QUESTION # 55
What is used to determine compressed air cleanliness?
- A. Profilometer
- B. Needle pressure gauge
- C. Psychrometer
- D. Blotter test
Answer: A
NEW QUESTION # 56
Which one of the following documents is the best source for coating technical data:
- A. Application Guidelines
- B. Specification
- C. Technical Data Sheet
- D. Safety Data Sheet;
Answer: C
NEW QUESTION # 57
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Taking measurements too far from the edge of a surface
- B. Failing to determine the base metal reading (BMR)
- C. Rotating the dial too fast when taking measurements
- D. Measuring ditty, tacky, or soft films
Answer: B,C,D
NEW QUESTION # 58
Polymerization is the process of:
- A. All thermoplastic coatings
- B. Monomers joining together
- C. All organic coatings
- D. Monomers telegraphing
Answer: B
NEW QUESTION # 59
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION # 60
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 5 to 6 mils (125 to 150 microns)
- B. 8 to 10 mils (200 to 250 microns)
- C. 6 to 7 mils (150 to 175 microns)
- D. 10 to 12 mils (250 to 300 microns)
Answer: C
NEW QUESTION # 61
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept the assignment without hesitation
- B. Review the NACE Attestation prior to making a decision
- C. Advise the prospective employer that you cannot accept the position
- D. Meet with the prospective employer to determine the scope of your role
Answer: D
NEW QUESTION # 62
If inspectors identify issues of non-conformance during an inspection, they should
- A. perform additional tests secretly to ensure there are no other potential issues at the site
- B. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. instruct the contractor's personnel in how to correct the issue so the project is not delayed
Answer: C
NEW QUESTION # 63
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 90% of the specified maximum thickness
- B. 100% of the specified maximum thickness
- C. 70% of the specified maximum thickness
- D. 80% of the specified minimum thickness
Answer: D
NEW QUESTION # 64
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. If the steel is pitted more coating will be required
- C. The Inspector may have to reject the Steel
- D. It affects the final appearance after blasting
Answer: C
NEW QUESTION # 65
Checking is
- A. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- B. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
Answer: D
NEW QUESTION # 66
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION # 67
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the PPE used by the Applicators
- B. Act in accordance with the site safety requirements and set an example
- C. Check the credentials of the Safety Officer on site
- D. Assume the role of the Safety Inspector
Answer: B
NEW QUESTION # 68
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 69
A magnetic pull-off type gauge is a good choice when:
- A. When working on non-ferrous metals
- B. When an intrinsically safe tool is required
- C. Performing an adhesion test
- D. Accuracy is not required
Answer: B
NEW QUESTION # 70
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor
- B. Document the problem and advise the Contractor and Owner's representative
- C. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- D. Break the blisters to see what's inside
Answer: B
NEW QUESTION # 71
Solvents are added to coating formulations to
- A. increase film permeability.
- B. provide color.
- C. dissolve binders and form liquid coatings.
- D. decrease film permeability.
Answer: C
NEW QUESTION # 72
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Hand tools
- B. Airless spray equipment
- C. Power tools
- D. Abrasive blast nozzles
Answer: C
NEW QUESTION # 73
......
Earn Quick And Easy Success With NACE-CIP1-001 Dumps: https://www.pass4guide.com/NACE-CIP1-001-exam-guide-torrent.html
Top-Class NACE-CIP1-001 Question Answers Study Guide: https://drive.google.com/open?id=1b0WYe69Up32GRarID4z1vqMqU8qJM1Pn